SFPs m. erw. Temp.

The KN-BTPMC-202M links two 10/100/1000TX copper ports to two SFP ports for 100/1000 Mbit/s and is mounted on a DIN rail. Both copper ports supply power to IEEE 802.3af/at/bt with up to 90 W per port, and a maximum of 180 W of PoE power is available across the two ports together. Power is fed redundantly with 48-57 VDC, and at least 52 VDC for PoE++; consumption ranges from 18 W without PoE to 200 W under full PoE load. Administration runs under IPv4 and IPv6 via web, Telnet, serial console, CLI, uPnP and SNMP v1/v2c/v3, complemented by PoE monitoring, PoE scheduling, PoE priority and a PD alive check that reboots end devices automatically. RSTP and ERPS, tag-based VLAN with 4k VLANs and IEEE 802.1X, RADIUS, TACACS+ and SSL/SSH cover redundancy and access protection. The operating temperature range is -40 to +75 C, the housing measures 42 x 118 x 145 mm and thermal power loss is 104 BTU/h. DIN rail mounting2 x 10/100/1000TX with PoE 802.3af/at/bt, 180 W in total2 x 100/1000 Mbit/s SFPPower supply 48-57 VDC, redundantOperating temperature -40 to +75 CManagement via web, CLI and SNMP v1/v2c/v3

This managed layer 2 and layer 3 switch in 19-inch format provides 24 copper ports 10/100/1000BaseT with RJ45 plus PoE and PoE+, complemented by four SFP/SFP+ ports for 1G/10G. The backplane delivers 128 Gbit/s and operation is fanless across a range of -40 to +75 C. Power is fed with 90-264 VAC at 50-60 Hz and with 48-57 VDC, redundantly and with at least 50 VDC for PoE+; consumption is a maximum of 26 W without PoE, and with PoE 348 W on AC feed only and 720 W on AC/DC or DC-only feed. Configuration runs over console, web GUI, mini USB and SNMP v1, v2c and v3, with static routing for IPv4 and IPv6 unicast, RIP v1/v2 and PTP to IEEE 1588 V2. A switching contact with DO up to 1 A at 24 VDC and a DI input is fitted, and configuration and firmware can be uploaded automatically via USB. The housing measures 440 x 44 x 331 mm, and MTBF is 266'508 h at 25 C and 158'506 h at 40 C. 19-inch switch, fanless24 x 10/100/1000BaseT with PoE and PoE+, RJ454 x SFP/SFP+ 1G/10G, 128 Gbit/s backplanePower supply 90-264 VAC and 48-57 VDC, redundantLayer 3 routing, RIP v1/v2, PTP IEEE 1588 V2Operating temperature -40 to +75 C

The LT-L802GBTME is a managed industrial switch for DIN rail mounting with eight 10/100/1000TX copper ports and two SFP ports for 100/1000 Mbit/s. The two optical ports allow a fault-tolerant fibre ring to be built that closes again in less than 50 ms after an interruption. The backplane delivers 20 Gbit/s, the MAC table holds 8k entries, and static layer 3 routing, up to 64 VLAN IDs to 802.1Q and link aggregation with 802.3ad LACP and static trunks are supported. Access runs through web server, Telnet, CLI, SSH, SSL, RMON, TFTP, USB and SNMP v1/v2/v3, joined by an RS232 console at 115.2 kBit/s on RJ45 and a USB configuration port for firmware updates, backup, restore and syslog. Power is fed redundantly with 12-48 VDC over screw terminals at a maximum draw of 15 W. The housing measures 142 x 56 x 99 mm and the operating temperature range is -40 C to +75 C. DIN rail mounting, no PoE8 x 10/100/1000TX, RJ452 x 100/1000 Mbit/s SFPRing recovery in less than 50 msPower supply 12-48 VDC, redundant, max. 15 WOperating temperature -40 C to +75 C

This variant of the managed DIN rail switch is set up for integration into the Bosch PAVIRO and Dynacord PROMATRIX systems. It offers eight 10/100/1000TX copper ports with RJ45 and two SFP ports for 100/1000 Mbit/s, which allow a fault-tolerant fibre ring with a recovery time below 50 ms. The backplane delivers 20 Gbit/s, the MAC table holds 8k entries, and static routing for IPv4 and IPv6 unicast, up to 64 VLAN IDs to 802.1Q and trunking with 802.3ad LACP are available. The switch is operated through web server, Telnet, CLI, SNMP v1/v2/v3, TFTP, SSH, SSL, RMON and USB, complemented by an RS232 console on RJ45. Redundant power is fed with 12-48 VDC over screw terminals at a maximum of 15 W; the housing measures 142 x 56 x 99 mm and works from -40 C to +75 C. Set up for Bosch PAVIRO and Dynacord PROMATRIXDIN rail mounting, no PoE8 x 10/100/1000TX, RJ452 x 100/1000 Mbit/s SFPPower supply 12-48 VDC, redundant, max. 15 WOperating temperature -40 C to +75 C

The LT-L804GBTME combines eight 10/100/1000TX copper ports with four SFP ports for 100/1000 Mbit/s and is mounted on a DIN rail. The optical ports allow fault-tolerant fibre rings that close again in less than 50 ms after an interruption. The backplane delivers 24 Gbit/s and the MAC table holds 8k entries, joined by static layer 3 routing, up to 64 VLAN IDs to 802.1Q, link aggregation with 802.3ad LACP and class of service to IEEE 802.1p with four priorities per port. Management is reachable via web server, Telnet, CLI, SNMP v1/v2/v3, TFTP, SSH, SSL, RMON and USB, plus an RS232 console on RJ45 and a USB port for firmware, backup, restore and syslog. Power is fed redundantly with 12-48 VDC over screw terminals; the housing measures 142 x 56 x 99 mm and operates from -40 C to +75 C. DIN rail mounting, no PoE8 x 10/100/1000TX, RJ454 x 100/1000 Mbit/s SFP24 Gbit/s backplane, 8k MAC tablePower supply 12-48 VDC, redundantOperating temperature -40 C to +75 C

This managed DIN rail switch provides eight 10/100/1000TX copper ports with PoE+ to 802.3af/at, with a maximum of 240 W of PoE power available across all ports. Two SFP ports for 100/1000 Mbit/s act as the optical backbone and allow fault-tolerant rings that close again in less than 50 ms. The backplane delivers 20 Gbit/s and the MAC table holds 8k entries; static layer 3 routing, up to 64 VLAN IDs to 802.1Q and link aggregation with 802.3ad LACP are supported. Configuration runs over console, web server, Telnet, CLI, SNMP v1/v2/v3, TFTP, SSH, SSL, RMON and USB. Power is fed redundantly with 48-55 VDC over screw terminals, and 24-48 VDC suffices where no PoE is required; the switch itself draws a maximum of 15 W without PoE. The housing measures 142 x 56 x 99 mm and the operating temperature range is -40 C to +75 C. DIN rail mounting8 x 10/100/1000TX with PoE+ 802.3af/at, 240 W in total2 x 100/1000 Mbit/s SFPRing recovery in less than 50 msPower supply 48-55 VDC, redundantOperating temperature -40 C to +75 C

The LT-LPIGE-804GBTME offers eight 10/100/1000TX copper ports with PoE+ to 802.3af/at and a maximum PoE budget of 240 W across all ports. Four SFP bays for 100/1000 Mbit/s form the optical backbone and allow fault-tolerant rings with a recovery time below 50 ms. The backplane delivers 24 Gbit/s and the MAC table holds 8k entries, joined by static layer 3 routing, up to 64 VLAN IDs to 802.1Q and link aggregation with 802.3ad LACP. Available access paths are console, web server, Telnet, CLI, SNMP v1/v2/v3, TFTP, SSH, SSL, RMON and USB. Redundant power is fed with 48-55 VDC over screw terminals, while 24-48 VDC is enough without PoE; the switch draws a maximum of 15 W without PoE at 109 BTU/h thermal loss. It measures 142 x 56 x 99 mm and works from -40 C to +75 C. DIN rail mounting8 x 10/100/1000TX with PoE+ 802.3af/at, 240 W in total4 x 100/1000 Mbit/s SFP24 Gbit/s backplane, 8k MAC tablePower supply 48-55 VDC, redundantOperating temperature -40 C to +75 C

This industrial layer 2/3 switch for DIN rail mounting brings together four 10/100/1000TX copper ports with PoE to 802.3af/at/bt and two SFP ports for 100/1000 Mbit/s. Up to 360 W of PoE power is available across all copper ports, so cameras with high power demand can also be fed over the data cable. The backplane delivers 12 Gbit/s, the MAC table holds 8k entries, and static routing for IPv4 and IPv6 unicast covers up to 82 routes. Administration runs via web GUI, console, Telnet, SSHv2, RMON and SNMP v1, v2c and v3; individual management accesses can be disabled, and PoE configuration and PoE scheduling work per port. The CLI console uses RS232 over mini USB-B, while a USB-A 2.0 port serves firmware update, backup and restore. Power is fed redundantly with 48-55 VDC at a maximum of 11 W without PoE, and the compact housing measures 110 x 65 x 90 mm and operates from -40 C to +75 C. DIN rail mounting4 x 10/100/1000TX with PoE 802.3af/at/bt, 360 W in total2 x 100/1000 Mbit/s SFPStatic routing for IPv4 and IPv6, max. 82 routesPower supply 48-55 VDC, redundantOperating temperature -40 C to +75 C

This unmanaged media converter joins one 10/100/1000TX copper port with RJ45 and one SFP port for 100/1000BaseFX. The copper port acts as a PoE source to IEEE 802.3af, at and bt with up to 90 W, which also covers cameras with high power demand. Whether LC duplex or simplex is used depends on the SFP fitted. Power can be fed redundantly and amounts to 12-56 VDC without PoE, 48-56 VDC with PoE and 52-56 VDC for PoE++ from 30 W; without PoE the unit draws a maximum of 4 W. The converter meets protection class IP30, supports link fault pass through and carries FCC Class A and CE marking. MTBF is 1'315'800 h at 20 C and 199'000 h at 75 C, the housing measures 104 x 32 x 82 mm without connectors, and the operating range is -40 C to +75 C. DIN rail or wall mounting1 x 10/100/1000TX with PoE 802.3af/at/bt up to 90 W1 x 100/1000 SFPLink fault pass throughPower supply 48-56 VDC, redundantIP30 protection, -40 C to +75 C

The defining feature of this media converter is the PDOR function, which switches the PoE output off and on again remotely. Combined with the SFP autochecking function of the RY switches, connected devices such as IP cameras can be monitored and restarted automatically in the event of a fault; the connected switch has to support SFP autochecking for this. The unit works without management and links a 10/100/1000TX copper port with PoE to af/at/bt up to 90 W with an SFP port for 100/1000BaseFX, where LC duplex or simplex depends on the SFP type. Power is fed redundantly through 2 x 48-56 VDC, and consumption is a maximum of 4 W without PoE and a maximum of 94 W with PoE. Protection class IP30, an operating range of -40 C to +75 C and dimensions of 104 x 32 x 82 mm without plugs complete the profile, with MTBF at 1'360'600 h at 20 C and 209'900 h at 75 C. PDOR function for remote PoE controlDIN rail, table or wall mounting1 x 10/100/1000TX with PoE af/at/bt up to 90 W1 x 100/1000 SFPPower supply 2 x 48-56 VDC, redundantIP30 protection, -40 C to +75 C

The PC-HPMC101-GE is an unmanaged media converter with one 10/100/1000TX copper port and one 100/1000 SFP uplink. The copper port supports PoE-af at 15 W, PoE-at at 30 W and PoE++ up to 60 W. The device runs on 12-56 VDC without PoE and on 48-56 VDC in PoE operation, drawing a maximum of 4 W without PoE at a thermal loss of 28 BTU/h. The mounting accessories supplied allow fixing on a DIN rail or on a wall. The converter meets protection class IP30, carries FCC Class A and CE marking and operates from -40 C to +75 C; MTBF is 1'319'000 h at 20 C and 197'300 h at 75 C. DIN rail or wall mounting1 x 10/100/1000TX with PoE up to PoE++ 60 WUplink 1 x 100/1000 SFPPower supply 48-56 VDCIP30 protection, -40 C to +75 C

The PC-MC-101-E converts a 10/100BaseTX copper port on RJ45 with auto negotiation, auto MDI/MDI-X and full or half duplex onto an SFP slot for 100 Mbit/s. Through that SFP port the unmanaged media converter attaches to common central switches, and versions with fixed optics are available as well. It runs from 12-60VDC or 18-36VAC via screw clamp, drawing 2W with a thermal loss of 7 BTU/h. IP30 protection, an operating range of -40° to +75°C and an MTBF of 1'382'500h at 20°C make it suitable for remote sites. The enclosure measures 36 x 50 x 59 mm (WxHxD) at 0.12 kg net and mounts on a DIN rail. Operation together with VDSL SFPs of the PD-VDSL-SFP series is not possible. 10/100BaseTX copper port, RJ45, auto MDI/MDI-XSFP slot for 100 Mbit/sSupply 12-60VDC or 18-36VAC, screw clampOperating temperature -40° to +75°C, IP30DIN rail mounting, 36 x 50 x 59 mm

The PC-MC101-GE couples a 10/100/1000BaseTX copper port on RJ45 with an SFP slot for 100 or 1000 Mbit/s using LC connectors; the SFP data rate is selected by dipswitch. This lets the media converter attach to practically all common central switches. Auto negotiation, auto MDI/MDI-X, full and half duplex plus LFP (Link Fault Pass Through) are part of the feature set, while management is not provided. It is powered at 12-56VDC through screw clamps and draws 2W; no power supply unit is included and it must be ordered separately. With IP30 protection, an operating range of -40° to +75°C, dimensions of 59 x 36 x 50mm (WxHxD) and 0.12 kg net, the unit mounts on a DIN rail. It cannot be operated in combination with VDSL SFPs of the PD-VDSL-SFP series. 10/100/1000BaseTX copper port, RJ45SFP slot 100/1000 Mbit/s, LC connectorSFP data rate set by dipswitchLFP (Link Fault Pass Through)Supply 12-56VDC, power supply ordered separately

This industrial switch supplies five 10/100/1000TX copper ports, four of which deliver PoE+ to 802.3af/at, plus two 100/1000 SFP bays serving as an optical uplink. When powered with 12VDC the maximum PoE across all ports is 65W; switch-only operation is met by 9-56VDC while PoE operation needs 12-56VDC, both of which can be fed redundantly. Own consumption amounts to a maximum of 6W without PoE and 130W at full PoE load, with 49 BTU/h of thermal loss. The backplane reaches 10GBit/s, the MAC table 1k entries, and jumbo frames up to 9600 bytes are supported even at 100MBit/s. The housing measures 142x43x105mm (HxWxL) at 0.74 kg net, operates from -40°C to +75°C in IP30 and achieves an MTBF of 1'683'800h at 20°C. 5 x 10/100/1000TX, four of them with PoE+ 802.3af/at2 x 100/1000 SFP bays as uplinkSupply 9-56VDC without PoE, 12-56VDC with PoE, redundantBackplane 10GBit/s, MAC table 1kJumbo frames up to 9600 bytes, IP30

This media converter turns a 10/100/1000TX copper port with PoE+ into an optical uplink using an SFP for 100/1000 with LC duplex. Attached devices are powered over the copper port to 802.3af at 15W or 802.3at at 30W. Without PoE a supply of 12-56VDC suffices, while PoE operation requires 48-56VDC with redundant feeding provided for; own consumption is a maximum of 4W without PoE at 21 BTU/h thermal loss. The unmanaged unit works from -40°C to +75°C in IP30 and reaches an MTBF of 1'360'600h at 20°C and 209'900h at 75°C. It measures 104 x 32 x 82mm (HxWxL) excluding plugs, weighs 0.19 kg net and mounts on a DIN rail or a wall. 10/100/1000TX copper port with PoE+ up to 30WUplink 1 x 100/1000 SFP, LC duplexSupply 12-56VDC without PoE, 48-56VDC with PoE, redundantOperating temperature -40°C to +75°C, IP30DIN rail or wall mounting, 0.19 kg net

In a very compact format the PC-PMC101-GME combines a 10/100/1000BaseTX copper port on RJ45 with PoE+ and an SFP slot for 100 or 1000 Mbit/s. Depending on the module the SFP takes an LC connector in simplex or duplex, the data rate is set by dipswitch, and LFP (Link Fault Pass Through) is available. The copper port handles auto negotiation, auto MDI/MDI-X, full and half duplex, and powers attached devices to 802.3af at 15W or 802.3at at 30W. Power is applied at 48-56VDC via screw terminal, drawing 2W without PoE at 7 BTU/h thermal loss; a power supply unit must be ordered separately. The enclosure measures 59 x 36 x 50mm (WxHxD) at 0.12 kg net, works from -40° to +75°C in IP30 and cannot be combined with VDSL SFPs of the PD-VDSL-SFP series. 10/100/1000BaseTX copper port, RJ45, PoE+ up to 30WSFP slot 100/1000, data rate set by dipswitchLFP (Link Fault Pass Through)Supply 48-56VDC, power supply ordered separatelyVery compact 59 x 36 x 50mm format, DIN rail mounting

The PDOR (PD Optical Reboot) function allows the PoE output of this media converter to be switched off and on again remotely, so that attached IP cameras can be restarted in the event of a fault. For active monitoring and control the connected switch has to support the SFP auto-checking function. The converter joins a 10/100/1000TX copper port carrying PoE af/at up to 30W with an SFP slot for 100/1000 using an LC connector in simplex or duplex, whose data rate is set by dipswitch. Power arrives on two inputs at 48-56VDC in redundant form, with consumption of at most 4W without and 34W with PoE. At -40°C to +75°C, IP30 protection, 104 x 32 x 82mm (HxWxL) excluding plugs and 0.15 kg net, DIN rail, table and wall mounting are all possible. PDOR function for remote PoE control10/100/1000TX copper port, PoE af/at up to 30WSFP slot 100/1000, LC simplex or duplexRedundant supply 2 x 48-56VDCOperating temperature -40°C to +75°C, IP30

This fanless industrial switch for DIN rail mounting is managed, operates on Layer 2 and Layer 3 and supports DMS. Two or more of its connections can build fault-tolerant optical fibre rings to IEEE802.x, and after an interruption the ring closes again in less than 50ms. Eight copper ports of 10/100/1000TX with RJ45, Auto MDI/MDIX and auto-negotiation are provided alongside four SFP slots for 100/1000, plus an RS232 console port at 115,2kBit/s (8, N, 1, RJ45) and one digital input and one digital output contact. Backplane capacity is 24 GBit/s at a forwarding rate of 17.9 Mpps, the MAC table holds 8k entries, jumbo frames up to 9600 bytes are supported even at 100 Mbit/s, and PTP to IEEE1588 v2 and IEC 61588 is implemented. Redundant power of 12-50VDC is wired via screw terminals with 15W maximum consumption, and operation is permitted from -40°C to +75°C at 5% to 95% relative humidity, non-condensing. DIN rail mounting, fanless, Layer 2/3 with DMS8 x 10/100/1000TX, RJ45 and 4 x 100/1000 SFPRing structure, recovery in less than 50msBackplane 24 GBit/s, forwarding rate 17.9 MppsPTP to IEEE1588 v2 and IEC 61588Redundant supply 12-50VDC, max. 15W

Aimed at applications with high data loads such as video over IP and video streaming, this fanless 19″ switch with WebSmart management suits smaller installations thanks to its reduced range of functions. Its eight 10/100/1000TX copper ports with RJ45 deliver PoE+ to 802.3af (15W) and 802.3at (30W) with a maximum of 130W across all ports, while two SFP slots for 100/1000 serve the uplink. Cameras powered over PoE are monitored continuously: after a failure the switch restarts the camera and raises an SNMP alarm if the restart fails or if excessive power is drawn. The unit is ring-capable, offers a 20GBit/s backplane and an 8k MAC table, and is configured through a web GUI as well as SNMPv1, v2c and v3; no console port and no layer 3 functions are included. It is fed with 100-240VAC at 50-60Hz, drawing a maximum of 10W without PoE and 150W with PoE, works from 0°C to 50°C, measures 220 x 242 x 44mm and weighs 2.1 kg net. 19″ switch with WebSmart management, fanless, ring-capable8 x 10/100/1000TX with PoE+, max. 130W for all ports2 x SFP 100/1000 uplinkCamera and PoE monitoring with SNMP alarmBackplane 20GBit/s, MAC table 8kPower supply 100-240VAC, 50-60Hz

Dimensioned for networks with heavy data loads such as video over IP and video streaming, this managed 19″ layer 2 switch with DMS combines 24 copper ports of 10/100/1000TX with RJ45 and PoE+ to 802.3af/at, with a maximum of 370W available across all ports. Four SFP slots for 100/1000 act as uplinks and an RS232 console port with RJ45 completes the access options. Cameras fed by the switch are monitored and restarted automatically after a failure; if that does not succeed, or if excessive power is requested, an SNMP alarm is issued. The backplane delivers 56GBit/s, the MAC table holds 8k entries, and configuration runs over console, web GUI and SNMPv1, v2c and v3. Power comes from 100-240VAC at 50-60Hz with a maximum draw of 40W without PoE, the switch operates from 0°C to 50°C, measures 442 x 211 x 44mm and weighs 3.4 kg net. 19″ switch, layer 2, managed, ring capable, DMS24 x 10/100/1000TX with PoE+ 802.3af/at, max. 370W4 x 100/1000 SFP and RS232 console port, RJ45Camera and PoE monitoring with SNMP alarmBackplane 56GBit/s, MAC table 8kPower supply 100-240VAC, 50-60Hz

This 19″ layer 2/3 switch is built for applications with high data volume such as video over IP and video streaming, including multicast, and its compact format and reduced port count suit smaller installations or a remote position within a larger network. Ten copper ports of 10/100/1000TX with RJ45 are provided together with two combo ports usable either as SFP for 100/1000 or as 10/100/1000TX with RJ45; an RS232 console port with RJ45 is fitted, PoE is not. Layer 3 functions cover static routing for IPv4 and IPv6 unicast, and VLAN support includes 802.1Q tagging with up to 255 VLAN groups, Q-in-Q and private VLAN. A 20GBit/s backplane and jumbo frames up to 9600 bytes, also at 100MBit/s, address video transmission with all ports occupied, while the MAC table holds 32k entries. The ring-capable switch runs on 100-240VAC at 50-60Hz with a maximum of 25W, works from 0°C to 40°C, measures 220 x 134 x 44mm and weighs 1.6 kg net. 19″ switch, layer 2/3, managed, ring-capable10 x 10/100/1000TX, RJ452 combo ports 100/1000 SFP or 10/100/1000TXStatic routing for IPv4 and IPv6 unicastBackplane 20GBit/s, MAC table 32kPower supply 100-240VAC, 50-60Hz, max. 25W

This managed 19″ switch with DMS targets applications with high data volume such as video over IP and video streaming, multicast included, and its management scope also covers complex network requirements. It offers 24 copper ports of 10/100/1000TX with RJ45 plus two SFP slots for 100/1000 as an optical uplink; configuration runs over console, web GUI and SNMPv1, v2c and v3, and an RS232 console port with RJ45 is fitted. At layer 3 it supports static routing for IPv4 and IPv6 unicast, while VLAN handling covers 802.1Q tagging with up to 255 VLAN groups, Q-in-Q and private VLAN; link aggregation to IEEE 802.3ad LACP or as a static trunk provides 18 groups of 8 ports. The backplane delivers 52GBit/s, the MAC table holds 8k entries, and jumbo frames up to 9600 bytes are supported at 100MBit/s as well. Fanless and ring-capable, the switch is fed with 100-240VAC at 50-60Hz, draws 40W at most, works from 0°C to 40°C and measures 442 x 44 x 221mm at 2.8 kg net. 19″ switch, layer 2/3, fanless, ring redundant, DMS24 x 10/100/1000TX, RJ452 x 100/1000 SFP optical uplinkStatic routing for IPv4 and IPv6 unicastBackplane 52GBit/s, MAC table 8kPower supply 100-240VAC, 50-60Hz, max. 40W

Carrying 24 optical ports, this managed 19″ layer 2/3 switch is well suited to linking remote sites such as IP cameras and is designed for heavy data loads including video over IP and video streaming with multicast. Alongside 24 SFP slots for 100/1000 it provides four combo copper ports of 10/100/1000TX with RJ45 and an RS232 console port on DB9 with console cable; PoE is not offered. Its supply is redundant and can be taken from 100-240VAC at 50-60Hz as well as from 48VDC, with a maximum draw of 30W and 102 BTU/h thermal power loss. Static routing for IPv4 and IPv6 unicast is supported, together with 802.1Q VLANs of up to 4k VLAN IDs, Q-in-Q, private VLAN and link aggregation across 26 groups of four ports; the backplane reaches 48 GBit/s with a 32k MAC table. The operating range covers -20°C to 60°C and the chassis measures 442 x 212 x 44mm at 3.2 kg net. 19″ switch, layer 2/3, managed, ring-capable, DMS24 x 100/1000 SFP4 x 10/100/1000TX, RJ45, comboRedundant supply 100-240VAC and 48VDCBackplane 48 GBit/s, MAC table 32kOperating temperature -20°C to 60°C

This managed 19″ layer 2/3 switch pairs 24 SFP slots for 100/1000 with four additional SFP/SFP+ ports for 1G/10G, making it suitable for connecting remote sites such as IP cameras together with a fast uplink. Four copper ports of 10/100/1000TX with RJ45 and an RS232 console port on DB9 including console cable round off the equipment, while PoE is not provided. Power is fed redundantly from 100-240VAC at 50-60Hz and from 48VDC, with 30W maximum consumption and 102 BTU/h thermal power loss. For smooth video transmission with all ports occupied it offers a 128GBit/s backplane, a 32k MAC table and jumbo frames up to 9600 bytes, also at 100MBit/s; configuration runs over console, web GUI and SNMPv1, v2c and v3. The switch operates from -20°C to 60°C, measures 442 x 212 x 44mm and weighs 3.3 kg net. 19″ switch, layer 2/3, managed, ring redundant, DMS24 x 100/1000 SFP4 x SFP/SFP+ uplink at 1G/10G4 x 10/100/1000TX, RJ45Redundant supply 100-240VAC and 48VDCBackplane 128GBit/s, MAC table 32k

This managed 19″ switch with light core operates on layer 2 and layer 3 and is intended for applications with high data loads such as video over IP and video streaming including multicast; extensive security functions protect both the device itself and the network traffic. It provides two copper ports at 1G/2.5G/5G/10G and eight SFP/SFP+ ports for 1G/10G, plus an RS232 console port with RJ45 and console cable; PoE is not included. Besides static routing it supports dynamic methods with OSPFv2/v3 and RIPv1/v2, and administration is available through web GUI, DMS, SNMPv1, v2c and v3, console, Telnet and RMON, with individual management access methods able to be disabled. Backplane capacity is 200GBit/s and the MAC table holds 32k entries. The ring-capable unit is fed with 100-240VAC at 50-60Hz, draws 40W at most, carries a regulated fan, works from 0°C to 50°C and measures 220 x 242 x 44mm at 1.7 kg net. 19″ switch, layer 2 and layer 3, ring-capable, light core2 x copper 1G/2.5G/5G/10G8 x SFP/SFP+ at 1G/10GStatic and dynamic routing, OSPFv2/v3 and RIPv1/v2Backplane 200GBit/s, MAC table 32kRegulated fan, power supply 100-240VAC

Compact and managed with PoE+, this 19″ switch addresses applications with high data volume such as video over IP and video streaming including multicast, and its reduced port count suits smaller installations or a remote position. Eight copper ports of 10/100/1000TX with RJ45 supply PoE+ to 802.3af/at at 30 W and class 0-4 within a PoE budget of 130 W, joined by two combo ports usable as SFP for 100/1000 or as 10/100/1000TX with RJ45 and an RS232 console port with RJ45. Cameras powered over PoE are monitored continuously and restarted automatically after a failure. The backplane delivers 20GBit/s, the MAC table holds 32k entries, and layer 3 functions and ring capability are present. Fed from 100-240VAC at 50-60Hz, the switch draws a maximum of 40W without PoE and 170W with PoE, operates from 0°C to 40°C and measures 220 x 243 x 44mm at 2.4 kg net. 19″ switch, layer 2/3, managed, ring-capable, PoE+8 x 10/100/1000TX with PoE+ 802.3af/at, class 0-4PoE budget 130 W2 combo ports 100/1000 SFP or 10/100/1000TXBackplane 20GBit/s, MAC table 32kPower supply 100-240VAC, 50-60Hz

Developed for networks with high data loads such as video over IP and video streaming including multicast, this managed 19″ switch offers DMS and extensive layer 3 functions. Of its 26 copper ports of 10/100/1000TX with RJ45, 24 carry PoE+ to 802.3af/at, with a maximum of 185W across all ports; two combo ports as SFP for 100/1000 and an RS232 console port with RJ45 complete the connections. Cameras powered over PoE are monitored, restarted after a failure and reported by SNMP if a fault persists. Backplane capacity is 52GBit/s, the MAC table holds 8k entries, and layer 3 covers static routing for IPv4 and IPv6 unicast; configuration runs over console, web GUI and SNMPv1, v2c and v3. Supplied with 100-240VAC at 50-60Hz, it draws a maximum of 40W without PoE and 255W with PoE at 185W, works from 0°C to 40°C, measures 442 x 211 x 44mm and weighs 3.3 kg net. 19″ switch, layer 2/3, managed, ring redundant, DMS26 x 10/100/1000TX, 24 of them with PoE+ 802.3af/atMaximum PoE power 185W for all ports2 combo ports 100/1000 SFPBackplane 52GBit/s, MAC table 8kPower supply 100-240VAC, 50-60Hz

Designed for video networks with heavy data loads, video over IP and video streaming with multicast, this managed 19″ switch with DMS provides 26 copper ports of 10/100/1000TX with RJ45, 24 of which carry PoE+ to 802.3af/at, with up to 370W available across all ports. Two combo ports as SFP for 100/1000 serve the optical uplink and an RS232 console port with RJ45 is fitted. Cameras fed by the switch are monitored continuously and restarted automatically after a failure, otherwise an SNMP alarm is raised. The backplane reaches 52GBit/s with an 8k MAC table, and layer 3 functions as well as ring capability are available. Power is taken from 100-240VAC at 50-60Hz with a maximum draw of 40W without PoE and 450W with PoE at 370W; operation is permitted from 0°C to 40°C and the chassis measures 442 x 211 x 44mm at 3.5 kg net. 19″ switch, layer 2/3, managed, ring-capable, DMS26 x 10/100/1000TX, 24 of them with PoE+ 802.3af/atMaximum PoE power 370W for all ports2 combo ports 100/1000 SFPBackplane 52GBit/s, MAC table 8kThermal power loss 225 BTU/h

This managed 19″ switch with layer 2/3 functions, strong security features and 10GBit/s uplinks is built for applications with high data loads such as video over IP and video streaming including multicast. Eight copper ports of 10/100/1000TX with RJ45 deliver PoE+ to 802.3af (15W) and 802.3at (30W) with a maximum of 250W across all ports, two SFP/SFP+ ports run at 1G/10G, and an RS232 console port with RJ45 is available. The switch monitors PoE-powered cameras continuously and restarts them after a failure; Non Stop PoE and PTP to IEEE 1588 v2 are implemented. Administration covers HTTP/HTTPS, SSH, Telnet client, IPv6 management and SNMP v1, v2c and v3 with traps and USM, alongside web GUI, DMS, console and RMON; the backplane reaches 56GBit/s with a 16k MAC table. Supplied with 100-240VAC at 50-60Hz, the unit draws a maximum of 40W without PoE and 290W with PoE, carries a regulated fan, works from 0°C to 50°C and weighs 2.5 kg net. 19″ switch, layer 2/3, managed, ring-capable8 x 10/100/1000TX with PoE+, max. 250W for all ports2 x SFP/SFP+ at 1G/10GNon Stop PoE, PTP to IEEE 1588 v2Backplane 56GBit/s, MAC table 16kRegulated fan, power supply 100-240VAC

With 24 copper ports of 10/100/1000TX and RJ45 delivering PoE+ to 802.3af (15W) and 802.3at (30W) at up to 370W across all ports, this managed 19″ switch covers larger video networks, while four SFP/SFP+ ports at 1G/10G form the uplink. It works on layer 2 and layer 3, supports DMS and is dimensioned for high data loads such as video over IP and video streaming with multicast, with extensive security features protecting the device and the network traffic. Cameras fed by the switch are monitored continuously and restarted after a failure; Non Stop PoE and PTP to IEEE 1588 v2 are part of the feature set. Access is provided through HTTP/HTTPS, SSH, Telnet client, IPv6 management, SNMP v1, v2c and v3 with traps and USM, as well as web GUI, DMS, console and RMON; the backplane reaches 128GBit/s with a 32k MAC table. At 100-240VAC and 50-60Hz consumption is 40W at most without PoE and 410W with PoE, operation is permitted from 0°C to 45°C, and the chassis measures 442 x 211 x 44mm at 3.7 kg net. 19″ switch, layer 2/3, managed, ring-capable, DMS24 x 10/100/1000TX with PoE+, max. 370W for all ports4 x SFP/SFP+ at 1G/10GNon Stop PoE, PTP to IEEE 1588 v2Backplane 128GBit/s, MAC table 32kRegulated fan, operating temperature 0°C to 45°C

Operating on layer 2 and layer 3, this 19″ switch was developed for applications with high data loads such as video over IP and video streaming including multicast, and extensive security features protect the switch itself as well as the network traffic. It carries 24 copper ports of 10/100/1000TX with RJ45 and PoE+ to 802.3af (15W) and 802.3at (30W) with a maximum of 370W across all ports, plus four SFP/SFP+ ports at 1G/10G and an RS232 console port with RJ45. Cameras powered over PoE are monitored continuously and restarted after a failure, and Non Stop PoE is available. Beyond static routing it supports OSPFv2/v3 and RIPv1/v2; administration runs through web GUI, DMS, SNMPv1, v2c and v3, console, Telnet and RMON, with individual management access methods able to be disabled. The backplane delivers 128GBit/s with a 32k MAC table, and a supply of 100-240VAC at 50-60Hz results in 40W maximum without PoE and 410W with PoE; the unit has a regulated fan, works from 0°C to 50°C and weighs 3.3 kg net. 19″ switch, layer 2 and layer 3, ring-capable24 x 10/100/1000TX with PoE+, max. 370W for all ports4 x SFP/SFP+ at 1G/10GStatic and dynamic routing, OSPFv2/v3 and RIPv1/v2Non Stop PoE, regulated fanBackplane 128GBit/s, MAC table 32k

The highest port count in this range, this 19″ switch provides 48 copper ports of 10/100/1000TX with RJ45 and PoE+ to 802.3af (15W) and 802.3at (30W), with a maximum of 740W available across all ports. Four SFP/SFP+ ports at 1G/10G form the uplink and an RS232 console port with RJ45 is fitted. The device operates on layer 2 and layer 3, is dimensioned for high data loads such as video over IP and video streaming with multicast, and protects both switch and network traffic through extensive security features; cameras powered over PoE are monitored and restarted after a failure, and Non Stop PoE is available. Static and dynamic routing with OSPFv2/v3 and RIPv1/v2 are supported, and administration runs over web GUI, DMS, SNMPv1, v2c and v3, console, Telnet and RMON. Backplane capacity is 176GBit/s with a 32k MAC table; at 100-240VAC and 50-60Hz consumption is 40W at most without PoE and 780W with PoE, operation is permitted from 0°C to 50°C, and the chassis measures 442 x 375 x 44mm at 5.8 kg net. 19″ switch, layer 2 and layer 3, ring-capable48 x 10/100/1000TX with PoE+, max. 740W for all ports4 x SFP/SFP+ at 1G/10GStatic and dynamic routing, OSPFv2/v3 and RIPv1/v2Non Stop PoE, regulated fanBackplane 176GBit/s, MAC table 32k

The RY-LGSPTR23-26 is a managed 19-inch Layer 2/3 switch intended for networks carrying high data loads such as video over IP, video streaming and multicast. It offers 26 copper ports 10/100/1000TX on RJ45, 24 of them with PoE++ to 802.3af/at/bt and a maximum PoE budget of 920W across all ports, plus two combo SFP slots for 100/1000. Cameras powered over PoE are monitored continuously, restarted automatically after a failure and reported by SNMP if the restart does not succeed; the backplane delivers 52GBit/s and jumbo frames up to 9600 bytes are supported at 100MBit/s as well. Static routing for IPv4 and IPv6, up to 255 VLAN groups to 802.1Q including Q-in-Q and private VLAN, and an 8k MAC table cover demanding network structures. Power comes from 100-240VAC at 50-60Hz and can be made redundant with the additional RY-PS-TR920 supply; configuration runs over console, web GUI or SNMPv1, v2c and v3. 26 x 10/100/1000TX, 24 of them with PoE++ 802.3af/at/btMaximum PoE power 920W over all ports2 x 100/1000 SFP (combo)52GBit/s backplane, 8k MAC tableStatic IPv4/IPv6 routing, up to 255 VLAN groupsRedundant 100-240VAC supply, 442 x 330 x 44mm

Designed for data-intensive tasks such as video over IP and multicast streaming, this 19-inch Layer 2/3 switch combines 48 copper ports 10/100/1000TX with PoE+ on RJ45 and four SFP/SFP+ slots for 1G/10G. A maximum of 920W PoE is available across all ports, rising to 1840W with a second power supply unit, while consumption stays at 40W maximum without PoE. The backplane runs at 176GBit/s, the MAC table holds 32k entries, and Non Stop PoE keeps connected devices supplied even while the switch reboots. Management is available over HTTP/HTTPS, SSH, Telnet client, IPv6 management and SNMP v1, v2c and v3 with traps and USM; PTP to IEEE1588 v2 and IEC 61588 is supported. The unit is rated from 0°C to 45°C and is powered from 100-240VAC at 50-60Hz, with redundancy through the RY-PS-TR920 power supply. 48 x 10/100/1000TX with PoE+, RJ454 x SFP/SFP+ 1G/10G, 10GBit/s SFP data rateMaximum PoE power 920W over all ports176GBit/s backplane, 32k MAC tableIEEE 1588 v2 PTP, Non Stop PoE, controlled fanRedundant 110/230VAC supply, 8.4 kg gross

This industrial Layer 2/3 switch for DIN rail mounting addresses video networks and Ethernet ring structures at 10, 100 and 1000MBit/s to IEEE802.x. Six copper ports 10/100/1000TX are provided, four of them with PoE and PoE+ to 802.3af/at within a 120W budget across all ports, together with two SFP slots for 100/1000 used to build fault-tolerant fibre rings. Cameras fed over PoE are monitored continuously and restarted automatically after a failure; if that does not work, the switch raises an SNMP alarm. The backplane delivers 24GBit/s, the MAC table holds 8k entries, and up to 64 VLAN IDs can be managed port-based or to 802.1Q. Operation is rated from -40°C to +75°C at 5% to 95% relative humidity, non-condensing, with 48-57VDC supplied through screw terminals and optional redundancy. DIN rail mounting, 135x62x130mm6 x 10/100/1000TX, 4 of them PoE/PoE+ 802.3af/atMaximum PoE power 120W, 48-57VDC redundant supply2 x 100/1000 SFP, 24GBit/s backplaneOperating temperature -40°C to +75°CIEEE 1588 v2 PTP, up to 64 VLAN IDs

The RY-LPIGE-804GBTME is an industrial Layer 2/3 switch for DIN rail mounting, aimed at video networks and Ethernet ring structures to IEEE802.x. All eight copper ports 10/100/1000TX carry PoE and PoE+ to 802.3af/at at 30W and class 0-4 within a 240W budget, while four SFP slots for 100/1000 serve to build fault-tolerant fibre rings. One digital input contact and one digital output contact extend the monitoring, which checks PoE-powered cameras continuously and reports faults by SNMP. Backplane throughput is 24GBit/s and the MAC table holds 8k entries; configuration runs through the RS232 console port at 115.2kBit/s. The unit is rated from -40°C to +75°C at 5% to 95% relative humidity, and the 48-57VDC supply on screw terminals can be arranged redundantly. DIN rail mounting, IEEE 1588 v2 PTP8 x 10/100/1000TX with PoE/PoE+ 802.3af/at, class 0-4PoE budget 240 W4 x 100/1000 SFP, 24GBit/s backplaneDigital input and output contact48-57VDC redundant supply, -40°C to +75°C

For video networks with heavy data loads, this industrial Layer 2/3 switch provides eight copper ports 10/100/1000TX on RJ45, with ports 1 to 4 carrying PoE+ and ports 5 to 8 PoE++, within a maximum of 360W across all ports. Two SFP/SFP+ slots for 1G/10G form the backbone connection, the backplane delivers 56GBit/s and the MAC table holds 16k entries. Besides static routing, the device handles the dynamic protocols OSPFv2/v3 and RIPv1/v2 for IPv4 and IPv6, and it also supports S-VLAN as well as PTP to IEEE1588 v2 and IEC 61588. Non Stop PoE keeps connected PDs supplied during a reboot, and jumbo frames up to 10240 bytes are supported at 100MBit/s too. The fanless DIN rail housing measures 170x70x130mm, operates from -40°C to +75°C and runs on 48-56VDC; individual management interfaces can be switched off. DIN rail mounting, fanless, 170x70x130mm8 x 10/100/1000TX, 4 x PoE+ and 4 x PoE++, max. 360W2 x SFP/SFP+ 1G/10G, 56GBit/s backplaneOSPFv2/v3 and RIPv1/v2, 16k MAC tableNon Stop PoE, IEEE 1588 v2 PTP48-56VDC supply, -40°C to +75°C

This industrial Layer 2/3 switch for DIN rail mounting targets video networks and Ethernet ring structures at 10, 100 and 1000MBit/s to IEEE802.x. All eight copper ports 10/100/1000TX carry PoE, PoE+ and PoE++ with auto MDI/MDIX and auto-negotiation, a maximum of 480W PoE is available across those eight ports, and two SFP slots for 100/1000 complete the port layout. Should a ring be interrupted, it closes again automatically in under 50ms. The backplane delivers 24GBit/s, the MAC table holds 8k entries, and static routing is available for IPv4 and IPv6 unicast. Power arrives through screw terminals at 54VDC with optional redundancy, whereby PoE+ and PoE++ require at least 54VDC; operation is rated from -40°C to +75°C at 5% to 95% relative humidity. DIN rail mounting, 135x62x130mm8 x 10/100/1000TX with PoE, PoE+ and PoE++Maximum PoE power 480W over all eight ports2 x 100/1000 SFP, 24GBit/s backplaneRing recovery in less than 50ms54VDC redundant supply, -40°C to +75°C

As an industrial Layer 2/3 switch for DIN rail mounting, the RY-LPITE-804GBTME serves video networks and Ethernet ring structures to IEEE802.x at 10, 100 and 1000MBit/s. Of its eight copper ports 10/100/1000TX, ports 1 to 4 carry PoE, PoE+ and PoE++ with a maximum PoE output of 240W; four SFP slots for 100/1000 allow several fault-tolerant fibre rings to be built, which close again in less than 50ms after an interruption. Consumption reaches 15W maximum without PoE and 375W with PoE, while the backplane provides 24GBit/s alongside an 8k MAC table. Configuration is available via console, web server, Telnet, CLI, SNMP v1/v2/v3, TFTP, SSH, SSL, RMON and USB, and static routing covers IPv4 and IPv6 unicast. The 48-57VDC supply on screw terminals can be made redundant and requires at least 54VDC for PoE+ and PoE++. DIN rail mounting, 135x62x130mm8 x 10/100/1000TX, ports 1-4 with PoE, PoE+ and PoE++Maximum PoE power 240W4 x 100/1000 SFP, 24GBit/s backplaneIEC 61850 for power utility automation networks48-57VDC redundant supply, MTBF 25°C: 494'255h